| Quantity: | |
|---|---|
20FT ISO Tank for Toxci Yellow Phosphorus Stainless Steel Insulated Tank Container with Steam Heating System
inlet and outlet are sealed with nitrogen to isolate air and water sealed
Yellow Phosphorus tank Container 20ft stainless steel
stainless steel Tank Container with Heating Insulated System for transport Yellow Phosphorus
PHOSPHORUS WHITE, PHOSPHORUS YELLOW UN Number: 1381
for UN 1381, PHOSPHORUS, WHITE or YELLOW, UNDER WATER or IN SOLUTION
The effective volume of the tank is 20 cubic meters, the tank body is cylindrical, made of high-quality international 304 type stainless steel 6mm, stainless steel wave plate 4mm, 4 layers in total (each upper and lower C-shaped flow port is welded firmly with a 150 mm wide C-shaped stainless steel plate to prevent cracking), a feed inlet of the tank body is equipped with a discharge outlet, and the inlet and outlet are sealed with nitrogen to isolate air and water, a 530mm diameter Maintenance manhole, glass fiber insulation for tank body, plus 1mm stainless steel mirror panel protection
Tank Type: 20 ISO full frame collar tank, Type UN Portable Tank T14, insulated, steam
heated, fitted with top side rails.
Quantity: 100 units
Frame Dimensions: 20 x 8 x 8
Capacity: 14,500 Litres +/- 1%
M.G.W.: 36,000 kgs
Tare (est.): 3,450 kg ±5%
Max Payload: 32,550 kg
Working Pressure: 4 Bar
Test Pressure: 6 Bar
Design Temp: -40°C to +130°C
Max. Allowable Vacuum: 0.41 Bar
Vessel Material: SANS 50028-7 WNr 1.4402/14404 (C<0.03%), 316L stainless steel
Shell: Cold Rolled 2B finish
Ends: polished internally to 1.2 Micron CLA
Shell Thickness: Calculated thickness: 4.18mm Min.
Corrosion allowance: 0.2mm Manufacturing thickness: 4.4mm min.
Ends Thickness: Calculated thickness: 4.2 mm Min. after forming
Corrosion allowance: 0.2mm
Manufacturing thickness: 4.4mm Min. after forming
Frame Material: GB/T 1591 - Q345D
Frame to Shell: 304 stainless steel
Corner castings: ISO 1161 - 8 off
Vessel Design Code: ASME VIII Div 1 where applicable TEL
Fittings and Accessories: All control valves to be supplied by AZ, Germany.
Manway Assembly 1 x DN500 tongue and groove type flat bolted manlid with 2 lifting eyebolts
incorporating one off DN150 loading connection at centre. Gasket: PTFE
Top Discharge Assembly 1 x 2" ANSI 150# weld in pad fitted with 2" AZ-F2 fire safe flanged plug
valve complete with bolted blank flange retained by chain.
A full length 2" flanged siphon tube is fitted with tube guide and sump. The valve will be painted in Red and shall be marked with "Phosphorus". Gasket: VSP(PITA)
Weld-in pad fitted horizontally on top centre line.
Nitrogen Connection 1 x 1.5" ANSI 150# weld in pad fitted with 1.5" AZ-F2 fire safe flanged plug
valve complete with bolted blank flange retained by chain.
The valve will be painted in Blue and shall be marked with "Nitrogen". Gasket: VSP(PITA)
Weld-in pad fitted horizontally on top centre line.
Water Connection 1 x 2" ANSI 150# weld in pad fitted with a 2" to 1.5" adaptor flange and 1.5"
AZ-F2 fire safe flanged plug valve complete with bolted blank flange retained by chain.
The valve will be painted in Green and shall be marked with "Water". Gasket: VSP(PITA)
Weld-in pad fitted horizontally on top centre line.
Relief Valve Assembly 1 x DN 80 flanged pressure relief valve with flameproof gauze, fitted with
bursting disc and manometer.
Set pressure: valve 4.4 bar; disc rated at 4.84 bar. Weld-in pad fitted horizontally on top centre line.
Spill Boxes 2 top spill boxes with lockable aluminium covers provided as follows:-
Centre box with lid flat open to front contains Manway assembly and PR Valve.
Rear box with lid flat open to front contains Top outlet, Nitrogen connection and Water connection.
Drainage pipes made of 304 stainless steel fitted to each side of each box.
Walkway „A Type walkway, 475 wide aluminium „Q grating fitted as follows:-
2 full length walkways fitted with two transverse sections, one adjacent to the centre spill box, one across rear of tank.
Electrolytic barriers fitted between differing materials.
Insulation Tank insulated with 25mm PU outside plus 25mm rock wool inside where
possible. Tank ends insulated with rockwool.
Aluminium foil will be fitted between insulation and tank shell. External cladding: 0.8mm nominal Aluminium
Steam Heating 12 longitudinal runs heating coils, giving actual surface of heating 6.5
M2(effective heating area of 13 M2 )will be fitted.
The working pressure is 4 bar and the testing pressure is 6 bar Inlet connection and outlet connection are 1" BSP.
Stainless steel caps and chain will be fitted.
Thermometer 1 off, Dual scale thermometer, -40° C to 160° C, liquid filled, fitted on rear
end to lower left side.
Ladder 1-off, Aluminium with anti-slip rungs, fitted at the rear RHS of the tank. Electrolytic barrier tape will be positioned between any dissimilar metals.
Earthing Plate 1 off, welded to bottom frame rear end of tank
Document Holder 1 off, in tubular PVC
Decal Mandatory markings supplied and fitted, Owners logo decal artwork to be supplied by TWS, will make the logo decal and stick onto the tank.
Data Plate 1 off SS consolidated data plate as per code.
Internal Finish Longitudinal welds: as-welded
Circumferential welds: as-welded but with 400 mm ground flush at the bottom centre.
Entire internal surface chemically cleaned and passivated after completion of all welding and dressing.
External Finish Tank Shell: External surface of tank cleaned after completion of all welding
and testing.
Framework: All carbon steel frame parts will be shot blasted to Swedish standard SA2½ followed by the application of:-
Painting First coat: Intermediate: Final coat:
Hempadur Zinc (1536C) Hempatex Primer (1530C) Hempatex Hibuild (5643C) TOTAL
Colour Red
30 micron min DFT 40 micron min DFT 50 micron min DFT 120 micron min DFT RAL 3002
Delivery Conditions Purged with Nitrogen and delivered with 0.5 Bar pressure.
Delivery time: 50~100units during 3months~12months
Cargo carried: Yellow phosphorus UN1381
ASME Spot ASME Full
Stacking: Each container is approved for 10 high stacking
Design Approvals: IMDG T14, CFR 49, ADR/RID, CSC, TC, TIR, ISO, UIC, US/UK DOT
The pictures are for your reference only.
ISO Tank Container 20 FT For Hazardous Liquids
T4,T6,T7,T8,T9, T10,T11,T14,T50 portable tank;
Size : 20 feet
Length : +6.058- 6.06 m
Width : +2.438- 2.44 m
Height : 2.438/2.591- 2.60 m
| Specifications - ISO tank container manufacturers | ||
| Frame Dimensions (L x W x H) | 6058 x 2438 x 2591 mm | |
| Nominal Capacity | 20000 litre (±0.75%) | |
| Maximum Gross Mass | 36000 kgs | |
| Tare Mass | 4510 kg (± 3%) | |
| Design Temperature (Frame & Tank) | -40 to +130 °C | |
| Pressure | Working | 1.70 bar |
| Test | 2.65 bar | |
| Material | Tank (Shell & Ends) | SANS 50028-7 Type 1.4402/1.4404 (C≤0.03%) |
| Frame | SPA-H or equivalent | |
| Insulation | Shell | Rockwool (50kg/m3) 50mm thick on aluminium foil. |
| Ends | Glasswool (16kg/m3) thickness to suit on aluminium foil. | |
Steam Heating | 6 runs. 110mm width stainless steel 304. 1" BSP inlet, 1" BSP outlet both with captive caps and cable. 4 bar working pressure, 6 bar test with warning decals and markings. A condensate drain is fitted. | |
| Manhole | 500mm low profile, 8 point fixing with Super Tanktyt Lid seal. | |
Safety Relief Assembly | 1-off. 2½" BSP Supermaxi Highflow relive, without flameproof gauze. Pressure only set at +4.4 bar (63.8psi). The assembly is situated off centre on a tangential tank pad. | |
| Air Inlet assembly | DN 40 ball valve terminating with 1½" BSP connection and cap. The assembly is situated off centre on a tangential tank pad. | |
| Top Discharge | DN80 stainless steel 316 tank pad with a blind flange. The assembly is fitted on centre on a horizontal tank pad. | |
| Bottom Discharge | DN80 45° Univalve Internal Footvalve part no. TBC fitted with an integrated butterfly valve terminating with a 3" BSP spigot with 3" BSP blind cap and chain. | |
| Thermometer | A surface mounted analogue type is fitted to the rear end dished end of the tank. Dual scale -40°C to +160°C / -40°F to 320°F. The thermometer is fitted with a protection bar. | |
| Document holder | A clear plastic document holder ø110mm is fitted to the rear right hand side beam. A drain hole is provided at the lowest point. | |
| Calibration | A calibration plate marked in cm/litres is fitted on the spillbox side wall. No calibrated stainless steel grade dipstick and bracket fitted. | |
| Design Code | ASME VIII DIV. 1 | |
| Approval | IMDG, US DOT CFR 49, RID/ADR, CSC, TC, TIR / Customs, UIC, ISO 1496/3 | |
ISO Tank
1.Are you trading company or manufacturer ?
We are Group Corporation manufacturer ,have Group Factories Contractor.Don't worry,dear.We have joined the trade assurance,if the products have quality problems when you received them,the payments can be refund to you.
20FT ISO Tank for Toxci Yellow Phosphorus Stainless Steel Insulated Tank Container with Steam Heating System
inlet and outlet are sealed with nitrogen to isolate air and water sealed
Yellow Phosphorus tank Container 20ft stainless steel
stainless steel Tank Container with Heating Insulated System for transport Yellow Phosphorus
PHOSPHORUS WHITE, PHOSPHORUS YELLOW UN Number: 1381
for UN 1381, PHOSPHORUS, WHITE or YELLOW, UNDER WATER or IN SOLUTION
The effective volume of the tank is 20 cubic meters, the tank body is cylindrical, made of high-quality international 304 type stainless steel 6mm, stainless steel wave plate 4mm, 4 layers in total (each upper and lower C-shaped flow port is welded firmly with a 150 mm wide C-shaped stainless steel plate to prevent cracking), a feed inlet of the tank body is equipped with a discharge outlet, and the inlet and outlet are sealed with nitrogen to isolate air and water, a 530mm diameter Maintenance manhole, glass fiber insulation for tank body, plus 1mm stainless steel mirror panel protection
Tank Type: 20 ISO full frame collar tank, Type UN Portable Tank T14, insulated, steam
heated, fitted with top side rails.
Quantity: 100 units
Frame Dimensions: 20 x 8 x 8
Capacity: 14,500 Litres +/- 1%
M.G.W.: 36,000 kgs
Tare (est.): 3,450 kg ±5%
Max Payload: 32,550 kg
Working Pressure: 4 Bar
Test Pressure: 6 Bar
Design Temp: -40°C to +130°C
Max. Allowable Vacuum: 0.41 Bar
Vessel Material: SANS 50028-7 WNr 1.4402/14404 (C<0.03%), 316L stainless steel
Shell: Cold Rolled 2B finish
Ends: polished internally to 1.2 Micron CLA
Shell Thickness: Calculated thickness: 4.18mm Min.
Corrosion allowance: 0.2mm Manufacturing thickness: 4.4mm min.
Ends Thickness: Calculated thickness: 4.2 mm Min. after forming
Corrosion allowance: 0.2mm
Manufacturing thickness: 4.4mm Min. after forming
Frame Material: GB/T 1591 - Q345D
Frame to Shell: 304 stainless steel
Corner castings: ISO 1161 - 8 off
Vessel Design Code: ASME VIII Div 1 where applicable TEL
Fittings and Accessories: All control valves to be supplied by AZ, Germany.
Manway Assembly 1 x DN500 tongue and groove type flat bolted manlid with 2 lifting eyebolts
incorporating one off DN150 loading connection at centre. Gasket: PTFE
Top Discharge Assembly 1 x 2" ANSI 150# weld in pad fitted with 2" AZ-F2 fire safe flanged plug
valve complete with bolted blank flange retained by chain.
A full length 2" flanged siphon tube is fitted with tube guide and sump. The valve will be painted in Red and shall be marked with "Phosphorus". Gasket: VSP(PITA)
Weld-in pad fitted horizontally on top centre line.
Nitrogen Connection 1 x 1.5" ANSI 150# weld in pad fitted with 1.5" AZ-F2 fire safe flanged plug
valve complete with bolted blank flange retained by chain.
The valve will be painted in Blue and shall be marked with "Nitrogen". Gasket: VSP(PITA)
Weld-in pad fitted horizontally on top centre line.
Water Connection 1 x 2" ANSI 150# weld in pad fitted with a 2" to 1.5" adaptor flange and 1.5"
AZ-F2 fire safe flanged plug valve complete with bolted blank flange retained by chain.
The valve will be painted in Green and shall be marked with "Water". Gasket: VSP(PITA)
Weld-in pad fitted horizontally on top centre line.
Relief Valve Assembly 1 x DN 80 flanged pressure relief valve with flameproof gauze, fitted with
bursting disc and manometer.
Set pressure: valve 4.4 bar; disc rated at 4.84 bar. Weld-in pad fitted horizontally on top centre line.
Spill Boxes 2 top spill boxes with lockable aluminium covers provided as follows:-
Centre box with lid flat open to front contains Manway assembly and PR Valve.
Rear box with lid flat open to front contains Top outlet, Nitrogen connection and Water connection.
Drainage pipes made of 304 stainless steel fitted to each side of each box.
Walkway „A Type walkway, 475 wide aluminium „Q grating fitted as follows:-
2 full length walkways fitted with two transverse sections, one adjacent to the centre spill box, one across rear of tank.
Electrolytic barriers fitted between differing materials.
Insulation Tank insulated with 25mm PU outside plus 25mm rock wool inside where
possible. Tank ends insulated with rockwool.
Aluminium foil will be fitted between insulation and tank shell. External cladding: 0.8mm nominal Aluminium
Steam Heating 12 longitudinal runs heating coils, giving actual surface of heating 6.5
M2(effective heating area of 13 M2 )will be fitted.
The working pressure is 4 bar and the testing pressure is 6 bar Inlet connection and outlet connection are 1" BSP.
Stainless steel caps and chain will be fitted.
Thermometer 1 off, Dual scale thermometer, -40° C to 160° C, liquid filled, fitted on rear
end to lower left side.
Ladder 1-off, Aluminium with anti-slip rungs, fitted at the rear RHS of the tank. Electrolytic barrier tape will be positioned between any dissimilar metals.
Earthing Plate 1 off, welded to bottom frame rear end of tank
Document Holder 1 off, in tubular PVC
Decal Mandatory markings supplied and fitted, Owners logo decal artwork to be supplied by TWS, will make the logo decal and stick onto the tank.
Data Plate 1 off SS consolidated data plate as per code.
Internal Finish Longitudinal welds: as-welded
Circumferential welds: as-welded but with 400 mm ground flush at the bottom centre.
Entire internal surface chemically cleaned and passivated after completion of all welding and dressing.
External Finish Tank Shell: External surface of tank cleaned after completion of all welding
and testing.
Framework: All carbon steel frame parts will be shot blasted to Swedish standard SA2½ followed by the application of:-
Painting First coat: Intermediate: Final coat:
Hempadur Zinc (1536C) Hempatex Primer (1530C) Hempatex Hibuild (5643C) TOTAL
Colour Red
30 micron min DFT 40 micron min DFT 50 micron min DFT 120 micron min DFT RAL 3002
Delivery Conditions Purged with Nitrogen and delivered with 0.5 Bar pressure.
Delivery time: 50~100units during 3months~12months
Cargo carried: Yellow phosphorus UN1381
ASME Spot ASME Full
Stacking: Each container is approved for 10 high stacking
Design Approvals: IMDG T14, CFR 49, ADR/RID, CSC, TC, TIR, ISO, UIC, US/UK DOT
The pictures are for your reference only.
ISO Tank Container 20 FT For Hazardous Liquids
T4,T6,T7,T8,T9, T10,T11,T14,T50 portable tank;
Size : 20 feet
Length : +6.058- 6.06 m
Width : +2.438- 2.44 m
Height : 2.438/2.591- 2.60 m
| Specifications - ISO tank container manufacturers | ||
| Frame Dimensions (L x W x H) | 6058 x 2438 x 2591 mm | |
| Nominal Capacity | 20000 litre (±0.75%) | |
| Maximum Gross Mass | 36000 kgs | |
| Tare Mass | 4510 kg (± 3%) | |
| Design Temperature (Frame & Tank) | -40 to +130 °C | |
| Pressure | Working | 1.70 bar |
| Test | 2.65 bar | |
| Material | Tank (Shell & Ends) | SANS 50028-7 Type 1.4402/1.4404 (C≤0.03%) |
| Frame | SPA-H or equivalent | |
| Insulation | Shell | Rockwool (50kg/m3) 50mm thick on aluminium foil. |
| Ends | Glasswool (16kg/m3) thickness to suit on aluminium foil. | |
Steam Heating | 6 runs. 110mm width stainless steel 304. 1" BSP inlet, 1" BSP outlet both with captive caps and cable. 4 bar working pressure, 6 bar test with warning decals and markings. A condensate drain is fitted. | |
| Manhole | 500mm low profile, 8 point fixing with Super Tanktyt Lid seal. | |
Safety Relief Assembly | 1-off. 2½" BSP Supermaxi Highflow relive, without flameproof gauze. Pressure only set at +4.4 bar (63.8psi). The assembly is situated off centre on a tangential tank pad. | |
| Air Inlet assembly | DN 40 ball valve terminating with 1½" BSP connection and cap. The assembly is situated off centre on a tangential tank pad. | |
| Top Discharge | DN80 stainless steel 316 tank pad with a blind flange. The assembly is fitted on centre on a horizontal tank pad. | |
| Bottom Discharge | DN80 45° Univalve Internal Footvalve part no. TBC fitted with an integrated butterfly valve terminating with a 3" BSP spigot with 3" BSP blind cap and chain. | |
| Thermometer | A surface mounted analogue type is fitted to the rear end dished end of the tank. Dual scale -40°C to +160°C / -40°F to 320°F. The thermometer is fitted with a protection bar. | |
| Document holder | A clear plastic document holder ø110mm is fitted to the rear right hand side beam. A drain hole is provided at the lowest point. | |
| Calibration | A calibration plate marked in cm/litres is fitted on the spillbox side wall. No calibrated stainless steel grade dipstick and bracket fitted. | |
| Design Code | ASME VIII DIV. 1 | |
| Approval | IMDG, US DOT CFR 49, RID/ADR, CSC, TC, TIR / Customs, UIC, ISO 1496/3 | |
ISO Tank
1.Are you trading company or manufacturer ?
We are Group Corporation manufacturer ,have Group Factories Contractor.Don't worry,dear.We have joined the trade assurance,if the products have quality problems when you received them,the payments can be refund to you.
